Items where Subject is "T Technology > TS Manufactures"

Up a level
Export as [feed] Atom [feed] RSS 1.0 [feed] RSS 2.0
Group by: Creators | Item Type
Jump to: A | B | D | E | F | G | H | J | K | M | N | P | Q | R | S | T | V | Y | Z
Number of items at this level: 66.

A

Aali, Tahmineh (2014) Improvement of heat transfer during hot pressing in medium density fiberboard manufacturing using zinc oxide nanoparticles. Masters thesis, University of Zabol.

Ahmadyousefi Jeshar, Saleh (2018) Assessment of the joint resistant in extrusion–flat pressed wood plastic composites affected by the content and type of mineral fillers. Masters thesis, University of Zabol.

Ailyari Boroujeni, Hadi (2015) Effect of isocyanate, maleic anhydride polypropylene and amplifiers as nano silica, nano-clay on the physical and mechanical properties of wood plastic composite. Masters thesis, University of Zabol.

Akbari, S. (2014) Effect of resin melamine/urea formaldehyde ratio and moisture content of mat on the particle board physical and mechanical properties made from Canola stalks and Poplar. Masters thesis, University of Zabol.

Arab, H. (2016) The effect of ash wood on the physical and mechanical properties of wood-plastic composite. Masters thesis, university of zabol.

Asad dollahpuor, H. (2016) Improvement of cement – bonded particleboard properties made from giant reed normal (Phragmites australis) and bagasse by nano silica (SiO2) additive. Masters thesis, University of Zabol.

Asadpour, Hamideh (2013) Made of Water Resistance Plywood Without any adhesive (Green Plywood). Masters thesis, University of Zabol.

Asefi Hedayat Abad, M. (2015) Reduction of Emissions of Formaldehyde from Urea-Formaldehyde (UF) Resins Using Boards Made With Urea Additive. Masters thesis, University of Zabol.

B

Babazadeh Lehi, Ali (2016) Efect of melamine veneer paper use on the properties of particleboard made from waste Medium-density fibreboard and particleboard. Masters thesis, University of Zabol.

Bahrami, Mohammad (2016) Lightweight Sandwich Panele construction with Porous Core Layer compressed newspaper. Masters thesis, university of zabol.

beiki, z. (2015) The effect of ratio of surface layer thickness to middle layer and melamine formaldehyde to urea formaldehyde on properties of particle board made by cotton stalk. Masters thesis, University of zabol.

D

Dalirzadeh, Amin (2013) Effect of Waste Carton Powder as Extender to Urea-formaldehyde Resin on Properties of MDF Made from Mixture of Bagasse and Waste MDF. Masters thesis, University of Zabol.

Dehdast, Fatemeh (2013) Effect of Nano-clay and oxidize polypropylene on properties of wood plastic composite made from Phragmites australis and urban plastic. Masters thesis, University of Zabol.

E

Ebrahimi, N. (2016) Functional characterization of composite products, paper - plastic made from recycled polymers. Masters thesis, University of Zabol.

F

Faegh, Masoud (2013) Manufacture of Laminated Strand Lumber and Oriented Strand Lumber made from Paulownia and Poplar wood by Urea-formaldehyde resin containing Nano clay. Masters thesis, University of Zabol.

Falahat Nezhad, A. (2016) Study and manufacturing green Particleboard with the natural Adhesive combination of Corn Flour/ Soy Flour. Masters thesis, university of zabol.

G

Ghaderi, Azam (2015) A comparison of two mixing techniques: Internal mixer, rotary drum blender and the properties of wood plastic composite. Masters thesis, University of Zabol.

Ghaffarani Maleki, Naser (2016) The effect of anatomical features and content of fillers apple branches and stems of cotton on the functional properties of wood-plastic composites. Masters thesis, University of Zabol.

H

Haghpanah, Mohammad (2014) The effect of using scrap fabric and nanoclay particles on the physical and mechanical properties of wood plastic camposite. Masters thesis, University of zabol.

Hasannejad, Abolghasem (2015) Synthetic resin Tannin-Lignin-Phenol-Resorcinol- Formaldehyde (TLPRF) and its mechanical properties using three Beech, Abies and Popular. Masters thesis, university of zabol.

Hashemi, M. (2014) Manufacture of particleboard by using combination adhesives from corn flour/black liquor. Masters thesis, university of zabol.

Hassanzadeh, M. (2014) Mechanical properties of wood composites reinforced concrete timber with concrete thickness and reinforcement arrangement scheme. Masters thesis, University of Zabol.

Hemati, T. (2015) Effect of joints number and layer arrangements of elements on mechanical behavior of chair made from small diameter Poplar timberand Methods improving the resistance of chair. Masters thesis, University of Zabol.

Hojjat, Hosein (2014) Study of effective parameters on edge strength properties in medium density fiberboard. Masters thesis, university of zabol.

Hoseini Aghbal, S. (2013) Evaluation of Cement-Bonded Particleboard Properties Made from Bagasse (Sugar Cane). Masters thesis, University of Zabol.

J

Jafari Ghalebig, A. (2014) Apply effect of digestion lingo cellulosic fibers by system of ruminants on the physical and mechanical properties of wood- plastic composite. Masters thesis, University of Zabol.

Jahani Lomer, Zahra (2013) Developing interactive computer software for Predict density profile effective physical and Mechanical properties of particleboard. Masters thesis, University of Zabol.

Jamshidzadeh, M. (2013) Comparison of mechanical strength of mortise and tenon and dowel joints in wooden chairs. Masters thesis, University of Zabol.

K

Kamali Moghadam, S. (2013) Determination of physical and mechanical Properties of parallel strand lumber woodplastic Composite made from waste of round Cut and recycled plastic. Masters thesis, University of Zabol.

Kameshki, B. (2015) Evaluation of particleboard treated with Preservation material (ACQ, and Evaluate of the durability of wood BFCA and Chlorothalonil) products against termite attack. Masters thesis, University of Zabol.

Kiani, Somaye (2017) The possibility of making the High Pressure Laminate from waste paper and its using as strengthen the surface particleboard. Masters thesis, university of zabol.

M

Mashayekhi, D. (2018) Experimental study of the effect of screw and plate on the behavior of glulam beam. Masters thesis, university of zabol.

Masoudi far, Masih (2014) The effect of chemically treatment of wood material on the characteristics of hybrid Nano composites of polypropylene-Nano Titanium dioxide TiO2. Masters thesis, University of zabol.

Mazlom Ali Abadi, Davood (2016) Effects of wheat straw and wood industries fiber size and content and characteristics on the properties applied of composites. Masters thesis, University of Zabol.

Mehmandoost, Manizheh (2019) The application of rotational wood welding technology in making the wood I-joist beam from abies and poplar wood. Masters thesis, university of zabol.

Mir, Samane (2014) Lightweight particleboard using expanded polystyrene (EPS). Masters thesis, University of Zabol.

Moazami, V. (2014) Effect of joint type of the middle layer wood stripes, veneer wood species and ratio of melamine / urea formaldehde on the properties of blockboard. Masters thesis, University of Zabol.

Moeel, Fatemeh (2013) Synthesis and determination characterizations of Phenol Resorcinol Formaldehyde resin (PRF). Masters thesis, university of zabol.

Mohebbi Gargari, Rahim and Bayat Kashkoli, Ali and Moazami, Vahid (2018) Determination and prioritization of effective criteria for sustainable development of wood framing in Iran by AHP technique. Technical Report. University of Zabol.

Molashahi, A. (2018) A comparison study on the machining properties of particleboard and medium density fiberboard made in iran. Masters thesis, university of zabol.

Morshed, M. (2014) Properties of cross-laminated timber (CLT) made from Poplar. Masters thesis, University of Zabol.

N

Neysi, Foad (2014) Artificial neural network to optimize particleboard manufacturing process (Case study: physical properties). Masters thesis, University of Zabol.

Niroomand, Farzad (2014) Effect of Filler Material and Amount of Maleic Anhydride on Physical-Mechanical Properties of Wood Plastic Composite. Masters thesis, University of Zabol.

Nosrati Pouyani, Mohammad (2017) Influence of electron beam irradiation on physical and mechanical properties of wood-plastic composites made from wood flour/HDPE. Masters thesis, university of zabol.

P

Pahang, H. (2017) The Performance Study of the Core layer of Sandwich panel Manufactured from Reed(Phragmites australis) Paerticles. Masters thesis, university of zabol.

Poodineh Zaboli, M. (2019) Effect of chemical treatment of lignocellulosic fibers on the physical and mechanical properties of banana fiber/polypropylene